I. A. GUZOVA, N. A. HODOSOVSKAYA, I. A. KOVALEVA High quality of purchased resources plays a critical role under the conditions of severe international competition. Raw materials, materials and components are purchase for product production and their quality is an essential part in the production of steel at OJSC “BSW – Management Company of the Holding “BMC” holding». The problem of excessively high level of dynamic loads is especially acute for roughing stands. The main reasons for dynamic overloads are intense transient processes occurring in the rolling cycle, the presence of elastic constraints and gaps in the system, imperfection of electric drive system and errors made during development. Therefore, there is a need for selection of material and manufacturing technology for mill rolls capable to withstand such loads for a sufficiently long period. Investigations of destruction causes of experimental mill roll of stand roughing group of mill 150 of section rolling shop at OJSC “BSW – Management Company of the Holding “BMC” holding were carried out. Main classification features are established based on the analysis of the fracture. The results of metallographic studies of microstructure and chemical composition of central and subsurface zone roll fragments are presented. The reason of destruction of experimental mill roll was discovered – nonconformance of roll material grade with the requirements of technological instructions and normative documentation for rough group of stands No. 1–3 Read more...

M. F. NOVIKOV, YU. I. KOZYREVA      One of the ways to increase the strength and reliability of building structures is the use of steel – fibre reinforced concrete. Steel – fibre reinforced concrete has significant advantages over conventional concrete. A high degree of resistance to cracking contributes to an increase in such physical and mechanical parameters as compressive, tensile and bending strength, water resistance, frost resistance, resistance to water and chemical penetration. In steel – fibre reinforced concrete, steel – fibre is used as a reinforcing material, evenly distributed over the volume of concrete. In the process of steel – fibre production, the fiber is cut with carbide knives. The article deals with the issues of increasing the wear resistance of carbide knives used for cutting steel – fibre, and suggests ways to increase the durability of cutting tools. The influence of the quality of tungsten- cobalt hard alloy on the wear resistance of knives is analyzed, and a knife attachment device is developed. Read more...

O. V. DAINEKO, L. F. KALINOVSKAYA, N. V. BESSEEMONOV     OJSC “BSW–Management Company of the Holding “BMC”, non-contact systems for measuring the outer diameters of products are widely used for measuring geometric dimensions. Diameter measurement systems are used to obtain reliable, true and accurate measurements. The method that provides continuous and non – contact control of these systems is the light -and – dark method of measuring the diameter. To ensure the reliability of the measurement results, the diameter measurement systems must undergo metrological control –calibration. Calibration is carried out according to the developed methodology, which specifies the order of work, requirements for standards, processing of measurement and evaluation results, and registration of calibration results. To assess the extended uncertainty, a mathematical model is created that takes into account all the corrections that affect the result of the assessment, each of which is subjected to a thorough analysis. Calibration of diameter measurement systems allows to evaluate their real deviations in operating conditions, which allows to ensure the accuracy and reliability of measuring the geometric dimensions of metal products at all stages of its production. Read more...

A. V. DAMARAD, V. P. SHCHERBAKOVA     The need to account for cost price occupies an important place in the enterprise management system. One of the important tasks of accounting for cost price is to control the cost of production. The cost price includes the total costs necessary for the enterprise to carry out production and commercial activities related to the production and sale of products, that is, everything that the enterprise costs to produce and sell products. To determine the economic benefits of selling the company’s finished products, it is necessary to know the final cost of the proposed contract. The amount of profit directly depends on the correctness of setting the sales price of products. This article discusses the assessment of the economic effect when modeling various contract positions based on the cost price of the enterprise, which will allow you to quickly solve production issues. The source data is information stored in the SAP ERP (Enterprise Resource Planning System) system: materials, component lists, component standards, etc. The source data processing and analysis system is SAP BI (Business Intelligence). To display the final result, we use a program designed for working with Microsoft Excel spreadsheets. Read more...